General Finishes RTM Stain 946ml

general-finishes-enduro-rtm-stain

General Finishes RTM Stain 946ml

$42.75

Compare
SKU: N/A Category:

Share this product

Description

General Finishes RTM Stain 946ml Ready To Match (RTM) Stain System for professional finishers makes color-matching a breeze. The system consists of 12 ready-to-use LOW VOC water-based stains, plus a clear base; a chip box with 96 color formulas on two-sided color chips plus stock color chips; and a formula book available in print/digital format to calculate any quantity of stain. Intermix the stains and base to design your own rich, deep wood stain colors. Brush or spray application. See our spray tip 

Always seal General Finishes Water Based Wood StainGeneral Finishes Dye Stain and General Finishes Enduro Ready-To-Match (RTM) Water Based Wood Stain with 3 coats of topcoat. More coats will not improve durability.

Grain Raise

After the first coat of topcoat has dried, you can knock down grain raise by lightly sanding with a 220 sanding pad. Watch Grain Raise video here.

Recommended Water-Based Topcoats FOR General Finishes RTM Stain 946ml
General Finishes High Performance can be applied by hand or sprayed; General Finishes Enduro Clear Poly is spray-only. Both topcoats dry clear and are great for high-use surfaces, such as kitchen cabinets and tabletops. General Finishes Flat Out Flat is our flattest topcoat, suitable for projects that do not receive major wear.

Recommended Oil-Based Topcoats FOR General Finishes RTM Stain 946ml
When sealing with General Finishes oil-based topcoats, General Finishes Arm-R-Seal and General Finishes Gel Topcoat, let water-based stain dry a minimum of 24 hours first. Oil-based topcoats amber increasingly over time.

Toning is the process of adding colorant (tinting), either dye or pigmented stain into a top coat and then applying over an entire piece in order to subtly deepen the color. All of GF water-based stains can be used: Stock base colors of RTM stains, Water-Based Wood Stains or Dye stains. If you are new to toning, we recommend starting with GF Dyes Stains, which can be easier to use as they only contain dyes and no pigments.

All of General Finishes water-based topcoats with the exception of Conversion Vanish can be tinted to create lightly colored finishes for toning.  It is YOUR RESPONSIBILITY TO TEST to your satisfaction before application to your entire project.

There are limits anytime you add pigments or dyes to water-based topcoats. Toning should always be done in small increments to achieve the desired color. If you are starting with a light honey tone door and you want to create an Espresso color this will take multiple coats of color including base coat of stain followed by several toning coats. It is impossible to achieve a radical change in color in coat application.

A good rule to follow when tinting is starting with a minimal amount of stain or dye, 5-10% by volume. Some colors work better than others. Normally 1-2 ounces or stain per quart of clear topcoat is sufficient to create a toner. Always test color first and strain material through a fine mesh filter to remove any undissolved particle of pigment. Once you have achieved the desired color tone apply a clear topcoat to lock in the color.

Some tinting recommendations are:

  • Do not exceed 13 ounces per gallon. Excess amounts of colorant can create surface defects and decrease the viscosity (causing drips, sag, etc.).
  • Tinting a product black only requires about 6 to 8 ounces (based on strength of colorant).

Additional information

Weight 1.1 kg
Dimensions 11.4 × 11.4 × 12.4 cm
Finishes

Bordeaux, Burnt Umber, Golden Brown, Raw Sienna, Raw Umber, Red, Tavern Brown, Tint Base Black, Tint Base White, Trans Red Oxide

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.